I spent a long time to find a solution making a puzzle from partial information from Google search.
Eggbot Inkscape Extension Download Utraedit FromAt the end I solved the problem in this way: 1) Download Utraedit from and install it.Connect USB and open Arduino IDE 3) Open TOOLS - SERIAL MONITOR and set BOTH NLCR 4) Type v (small v for Version): If it answer EBBv13andabove Protocol emulated by Eggduino-Firmware V1.6a, means that the connection is OK and the problem is in Inkscape driver 5) Open TOOLS - GET BOARD INFO and write somewhere the VID: and PID: numbers you read.
Search in C:Program FilesInkscapeshareextensions the file eggbotscanwin32.py and open it with ULTRAEDIT 7) Modify row 6 in eggbotscanwin32.py with your right VID and PID value and save. I am using mac 10.11. There is no file eggbotscanwin32.py but a eggbotscanlinux.py. But no way to enter the VID or PID (I know how to use vi, but I dont know how to program python). I all the time try to fix it but I cant do it succesfully yet. Im 19 years old. I am into designing, making, programming and electronics. In the future, I want to start a company and make my own products. I wanted to make it before but I thought it is too hard for me but I was wrong. Add Tip Ask Question Comment Download Step 1: Parts Below I add list of parts: Stepper motors Stepper motor drivers Arduino Power supply Micro Servo Plastic plate, wood 40cm screws x3 and 12 nuts for its Two lego wheels Markers in different colors Drill, knife, saw, screwdriver, double-sided tape, wood glue, wire, soldering iron, rubber bands Everything you need to make PCB link. Add Tip Ask Question Comment Download Step 2: Connection Connect it like on fritzing image above or go to the next step and make PCB (printable circuit board). And you must find right settings for potentiometer on stepper motors controller. With this potentiometer you can control voltage that goes to stepper motors. Try to set it that the stepper move is as smooth as it possible. Add Tip Ask Question Comment Download Step 3: PCB (optional) Why I made PCB Look at the image above, it shows how it looks on breadboard. Too many wires. You can easily connect something wrong or something can disconnect itself and you can spoil e.g: stepper motor driver. And on PCB everything looks better, take less place and is reliable in combined. Eggbot Inkscape Extension Pdf Download EGGAttachments EGG bot PCB v2etchcoppertop.pdf Download EGG bot PCB v2.fzz Download Add Tip Ask Question Comment Download Step 4: Frame The frame is made with plastic and some wood. Attachments eggbot.skp Download Add Tip Ask Question Comment Download Step 5: Cutting of the Frame Cut two elements from second picture and one from the third picture. Add Tip Ask Question Comment Download Step 6: Smoothing the Edge Smooth the edges with sandpaper to make them look better. Add Tip Ask Question Comment Download Step 7: Drilling Holes Drill holes like on image above. Add Tip Ask Question Comment Download Step 8: Pen Arm Pen arm is made with wood and plastic. At the end of the arm I made 9mm hole for marker Add Tip Ask Question Comment Download Step 9: Connection Frame I hope you understand how to connect all of parts of frame with this photo if you have problems with it, write a comment I will try to help. ![]() Eggbot Inkscape Extension Code For ArduinoAdd Tip Ask Question Comment Download Step 10: Code for Arduino Download code for arduino from here. And you need to change few lines: This: define YAXISDIRPIN 14 define YAXISSTEPPIN 15 To this: define YAXISDIRPIN 10 define YAXISSTEPPIN 11 and This: define XAXISDIRPIN 10 define XAXISSTEPPIN 8 To this: define XAXISDIRPIN 7 define XAXISSTEPPIN 8 and This: define SERVOPIN 13 To: define SERVOPIN 9 Add Tip Ask Question Comment Download Step 11: Software for Computer I propose to install original eggbot extension to inkscape because with it you can print filled object. To make G-code files in inkscape download this extension made by martymcguire. And the last thing to download is a program to sending commands over serial to arduino. Download it here. Now you need to change unicorn extension code. Go to: C:program filesinkscapeshareextensionsunicorncontext.py Add to 29 line this: M300 S0.2F (pen up) self.penupangle, And delete line 39: M300 S255 (turn off servo), Add Tip Ask Question Comment Download Step 12: First Painting This are first eggs that I painted by my eggbot.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |